| Journal Papers |
| 2012 |
| 1. | Imran M, Mativenga P T, Gholinia A, Withers P J. In Press. "Evaluation of surface integrity in micro drilling process for nickel-based". International Journal of Advanced Manufacturing Technology. |
| 2. | Saunders F, Gale A W. In Press. "Digital or didactic: Using learning technology to confront the challenge of large cohort teaching". British Journal of Educational Technology. DOI: 10.1111/j.1467-8535.2011.01250.x, Abstract |
| 3. | Hayhurst R J, Vakili-Tahami F, Hayhurst D R. In Press. "Verification of the 3-D Parallel CDM Software Damage XXX using 2-D Serial Software and Experimental Results, for Analysis of High-Temperature Creep Failure". International Journal of Pressure Vessels and Piping. |
| 4. | Quariguasi J, Bloemhof J. In Press. "An analysis of the eco-efficiency of remanufactured personal computers and mobile phones". Production and Operations Management. PDF |
| 5. | Chong P H, Liu Z, Skelton P, Crouse P. In Press. "Characterization and corrosion performance of laser-melted 3Cr12 steel". Applied Surface Science. Vol. 362. pp 247. |
| 6. | In Press. "Design of weld fillers for mitigation of residual stresses in ferritic and austenitic steel welds". Science and Technology of Welding & Joining. , Abstract |
| 7. | Dindarian A, Gibson A, Quariguasi J. In Press. "Electronic product returns and potential reuse opportunities: A microwave case study in the United Kingdom". Journal of Cleaner Production. March DOI: http://dx.doi.org/10.1016/j.jclepro.2012.03.015, Abstract |
| 8. | Saunders F, Jasper M, Whitton P. In Press. "Promoting collaborative learning in engineering management education through the use of wikis". Engineering. Vol. 5. No. 2. , Abstract |
| 9. | Ali S, Hinduja S, Atkinson J, Bolt P, Werkhoven R. In Press. "The effect of ultra-low frequency pulsations on tearing during deep drawing of cylindrical cups". International Journal of Machine Tools and Manufacture. |
| 10. | Yang S, Cooke K, Aramcharoen A, Mativenga P T, Teer D. In Press. "Micro-tool Coatings Using Magnetron Sputtering". Materials Technology: Advanced Performance Materials. |
| 11. | Chan PWC, Johansen E, Moor R. In Press. "Partnering paradoxes: A case of constructing inter-organisational collaborations in infrastructure projects". Project Perspectives. DOI: http://www.ipma.ch/Documents/Perspectives_2012.pdf, Abstract |
| 12. | K.Vacharanukul K, Mekid S. In Press. "Real-time Non-Contact Probe for In-Process Inspection using Gaussian Convolution Smooth Technique". Sensors and Actuators A: Physical. |
| 13. | Mekid S, Vaja D. In Press. "Propagation of Uncertainty: Expressions of Second and Third order Uncertainty with Third and Fourth Moments". Measurement. |
| 14. | Davey K, Hinduja S. In Press. "Modelling the Pressure Die Casting Process for the Rapid Casting of Flash-Free Components". Journal of Materials Processing Technology. |
| 15. | Hinduja S, Mansor A, Owodunni O. In Press. "Voronoi diagram-based linking of contour-parallel tool paths for 2½ D pocket machining". Computer-Aided Design. |
| 16. | Paddea S, Francis J A, Paradowska A, Bouchard P J, Shibli I A. 2012. "Residual Stress Distributions in a P91 Steel-Pipe Girth Weld before and after Post Weld Heat Treatment". Materials Science and Engineering A. Vol. 534. pp 663-672. DOI: 10.1016/j.msea.2011.12.024, Abstract |
| 17. | Fahad M, Mativenga P T, Sheikh M A. 2012. "A comparative study of multilayer and functionally graded coated tools in high-speed machining". International Journal of Advanced Manufacturing Technology. |
| 18. | Mark A F, Francis J A, Dai H, Turski M, Hurrell P R, Bate S K, Kornmeier J R, Withers P J. 2012. "On the Evolution of Local Material Properties and Residual Stress in a Three-Pass SA508 Steel Weld". Acta Materialia. Vol. 60. pp 3268-3278. DOI: http://d10.1016/j.actamat.2012.03.022, Abstract |
| 19. | Safdar S, Pinkerton A, Li L, Sheikh M A, Withers P J. 2012. "An anisotropic enhanced thermal conductivity approach for modelling laser melt pools for Ni-base super alloys". Applied Mathematical Modelling. DOI: 10.1016/j.apm.2012.03.028 |
| 20. | Heinemann R. 2012. "The Effect of Starting Hole Geometry on Borehole Quality and Tool Life of Twist Drills". International Journal of Advanced Manufacturing Technology. DOI: 10.1007/s00170-011-3625-7 |
| 21. | Turski M, Francis J A, Hurrell P R, Bate S K, Hiller S, Withers P J. 2012. "Effects of Stop-Start Features on Residual Stresses in a Multipass Austenitic Stainless Steel Weld". International Journal of Pressure Vessels and Piping. Vol. 89. pp 9-18. DOI: 10.1016/j.ijpvp.2011.08.006, Abstract |
| 22. | Heinemann R, Hinduja S. 2012. "A new strategy for Tool Condition Monitoring of small diameter twist drills in deep-hole drilling". International Journal of Machine Tools and Manufacture. Vol. 52. Issue 1. pp 69-76. January DOI: 10.1016/j.ijmachtools.2011.09.002 |
